-
Specifications
-
Standard/Optional Equipment
- Catalog
Minimum Rating
440BHP
Maximum Rating
595BHP
Emissions
EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA
Rated Speed
2100r/min
Bore
5.4in
Stroke
6.75in
Displacement
928in³
Aspiration
Turbocharged-Aftercooled
Governor and Protection
ADEM A3
Engine Weight - Net Dry
2743lb
Rotation from Flywheel End
Counterclockwise
Oil Change Interval
250
Flywheel and Flywheel Housing
SAE No. 0 or SAE No. 1
Flywheel Teeth
136 (SAE 0), 113 (SAE 1)
Minimum Cooling System - Engine Only
5.5gal (US)
Length
54in
Width
37in
Height
48in
Transmission Arrangement
Transmission cooler
Tool set
Air Compressor
Air chambers
Air compressor governor
Air Inlet System
Air cleaners
Precleaners
Air lines
Air inlet gasket
Charging System
Charging alternators
Alternator mountings
Alternator wiring
Circuit breaker mountings
Alternator belt guard
Cooling System
Radiator — installed
Radiator — ship loose
Fan drive f/u/w Caterpillar installed radiator
Fan drives for customer-supplied radiators
Fan height instructions
Vee belts for customer-supplied radiators
Aftercooler lines f/u/w Caterpillar installed radiator
Rear-facing exhaust
Aftercooler lines
Suction fan adapters — attaches fan to fan pulley
Blower fan adapter — attaches fan to fan pulley
Blower fan
Suction fan
Fan belt tightener
Coolant level sensor
Dry charge coolant conditioners
Dry charge coolant conditioner element
Exhaust System
Turbo exhaust connection
Flexible fitting
Elbows
Flanges
Dry elbow
Air Inlet System
Single turbocharger, mid-mounted, inlet 152.4 mm (6 in), hose connection
Control System
Electronic governing, PTO speed control
Programmable ratings
Cold mode start strategy
Automatic altitude compensation
Power compensation for fuel temperature
Programmable low and high idle and TEL
Electronic diagnostics and fault logging
Engine monitoring and protection system (speed, temperature, pressure)
J1939 Broadcast (diagnostic, engine status, and control)
Cooling System
Thermostats and housing — outlet vertical
Jacket water pump — gear-driven, centrifugal, RH
RH front water pump inlet
All plugs/fittings are STOR for lines gp water
Exhaust System
Exhaust manifold — dry
Front turbo exhaust
Full marmon connection, maximum load 10 kg for direct connection to turbo
Flywheels and Flywheel Housings
See Mandatory Options
Fuel System
MEUI system
Fuel filter, secondary, mid-mount (LH 2 micron high performance)
Fuel transfer pump, LH front
Fuel priming pump, LH mid-mount
Fuel sample valve, mounted on fuel filter base
Lube System
Crankcase breather — rear valve cover
Oil cooler — RH
Oil filter — RH
Oil pan — front sump
Oil filler — LH front
Oil dipstick — LH front
Oil pump
Oil valve sampling — on oil filter base
Mounting System
Front support (shipping only)
Power Take-Offs
Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm (11.5 in) 1 groove, all 15.9 mm (.63 in) width
Hydraulic pump drive, SAE A, 11 tooth
General
Vibration damper
Paint — Cat yellow
Lifting eyes
Automatic variable timing, electronic
Electronic installation kit 70-pin connector (connectors, pins, sockets)
Literature group owner and operator
Mandatory Options
Throttle position sensor
Exhaust system — front or rear
Flywheel housing or rear PTO
Primary filter/water separator
ALL
Air Inlet System
Single turbocharger, mid-mounted, inlet 152.4 mm (6 in), hose connection
Control System
Electronic governing, PTO speed control
Programmable ratings
Cold mode start strategy
Automatic altitude compensation
Power compensation for fuel temperature
Programmable low and high idle and TEL
Electronic diagnostics and fault logging
Engine monitoring and protection system (speed, temperature, pressure)
J1939 Broadcast (diagnostic, engine status, and control)
Cooling System
Thermostats and housing — outlet vertical
Jacket water pump — gear-driven, centrifugal, RH
RH front water pump inlet
All plugs/fittings are STOR for lines gp water
Exhaust System
Exhaust manifold — dry
Front turbo exhaust
Full marmon connection, maximum load 10 kg for direct connection to turbo
Flywheels and Flywheel Housings
See Mandatory Options
Fuel System
MEUI system
Fuel filter, secondary, mid-mount (LH 2 micron high performance)
Fuel transfer pump, LH front
Fuel priming pump, LH mid-mount
Fuel sample valve, mounted on fuel filter base
Lube System
Crankcase breather — rear valve cover
Oil cooler — RH
Oil filter — RH
Oil pan — front sump
Oil filler — LH front
Oil dipstick — LH front
Oil pump
Oil valve sampling — on oil filter base
Mounting System
Front support (shipping only)
Power Take-Offs
Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm (11.5 in) 1 groove, all 15.9 mm (.63 in) width
Hydraulic pump drive, SAE A, 11 tooth
General
Vibration damper
Paint — Cat yellow
Lifting eyes
Automatic variable timing, electronic
Electronic installation kit 70-pin connector (connectors, pins, sockets)
Literature group owner and operator
Mandatory Options
Throttle position sensor
Exhaust system — front or rear
Flywheel housing or rear PTO
Primary filter/water separator
Optional Equipment
Transmission Arrangement
Transmission cooler
Tool set
Air Compressor
Air chambers
Air compressor governor
Air Inlet System
Air cleaners
Precleaners
Air lines
Air inlet gasket
Charging System
Charging alternators
Alternator mountings
Alternator wiring
Circuit breaker mountings
Alternator belt guard
Cooling System
Radiator — installed
Radiator — ship loose
Fan drive f/u/w Caterpillar installed radiator
Fan drives for customer-supplied radiators
Fan height instructions
Vee belts for customer-supplied radiators
Aftercooler lines f/u/w Caterpillar installed radiator
Rear-facing exhaust
Aftercooler lines
Suction fan adapters — attaches fan to fan pulley
Blower fan adapter — attaches fan to fan pulley
Blower fan
Suction fan
Fan belt tightener
Coolant level sensor
Dry charge coolant conditioners
Dry charge coolant conditioner element
Exhaust System
Turbo exhaust connection
Flexible fitting
Elbows
Flanges
Dry elbow