ALL

Product Consist

The engine is a turbocharged, aftercooled, four-strokecycle- diesel, electronic unit injection engine with a 280 mm (11 in) bore by 300 mm (11.8 in) stroke. SAE standard rotation is counterclockwise as viewed from the rear of engine flywheel.

Emissions Certifications

GL and CCS approved IMO certificate — includes statement of compliance or Engine International Air Pollution Prevention (EIAPP) certificate, supplied by the Recognized Organization (RO) where available, and technical file to be kept on board per IMO regulations.

Marine Certification Society type-approval

ABS, BV, CCS, DnV, GL, LRS

Spray shielding to meet SOLAS regulations for flammable fluids

European Certifications

Declaration of Incorporation for EU Machinery Safety

Directive and EU Low Voltage Safety Directive

Air Inlet System

Fresh water aftercooler, corrosion resistant coated (air side)

Air inlet shutoff

Turbocharger, rear-mounted, oil lubricated

Control System

Single Cat ADEM A3 electronic engine control module with electronic unit injector fuel system, rigid wiring harness (10 amp 24V power required to drive electronic engine control modules)

Cooling System

Gear-driven jacket water (JW) pump

Gear-driven separate-circuit aftercooler/oil cooler (AC/OC) pump

Engine coolant water drains

Exhaust System

Dry, gas tight exhaust manifold

Fuel System

Distillate fuel (requires viscosity ranging from 1.4 cSt to 20 cSt at 38°C)

Fuel pump, gear-driven

Fuel transfer pump (mounted on left-hand side)

Duplex fuel filters, rear-engine-mounted

Electronically controlled unit injectors

Lube system

Centrifugal oil filters with single shutoff, service-side engine mounted on cylinder block inspection covers (includes installed oil lines and single shutoff valve), filters centrifuge bypass oil from the main lubricating oil pump (can be serviced with the engine running)

Oil filler and dipstick

Oil pressure regulating valve

Dry engine-mounted sump system that gravity feeds into base assembly integral sump

Engine-mounted duplex oil filter

Intermittent air prelube

Continuous electric prelube

Redundant prelube with continuous electric prelube and intermittent air prelube backup

Oil pan drain valves

Electric continuous prelube pump

Lube oil heater

Oil pump - gear drive

Protection System

Crankcase explosion relief valves

Alarm and shutdown during abnormal operation

Instrumentation

PLC-based system provides protection, monitoring, and control housed in a NEMA 4 (IP66) enclosure.

General

Service Literature

Optional Equipment

Air Inlet System

90° adapter and straight adapters for air inlet to turbocharger Air cleaners

Air cleaners with Cat dry paper filter elements (approximately 99.9% efficient at filtering SAE fine dust)

Soot filter

Control System

4-20 mA load feedback signal

Load sharing module

Direct rack module

Cooling System

Separate Circuit Aftercooler (SCAC)

Customer water connections

Jacket water thermostats

AC/OC thermostats

Accessory module-mounted high volume expansion tank

Jacket water heater

Heat recovery connections and thermostats for use with water maker system

ANSI connection adapters

Exhaust System

Exhaust manifold shields

Vertical or 30° outboard exhaust orientation options

Exhaust outlet expanders and weld flanges

Fuel System

Manual fuel priming pump

Duplex primary fuel strainer

Flexible fuel hose connections

Lube System

Dry engine-mounted sump system that gravity feeds into base assembly integral sump

Engine-mounted duplex oil filter

Intermittent air prelube

Continuous electric prelube

Redundant prelube with continuous electric prelube and intermittent air prelube backup

Oil pan drain valves

Electric continuous prelube pump

Lube oil heater

Protection System

Wiring meets MCS requirements

Upgrade PLC monitor to industrial PC

Upgrades AC/OC, JW and start air pressure from contactors to transducers

Raw water/sea water pressure transducer

Modbus communication

Beacon and horn

Single engine remote display monitor

Emergency pump start signal

Cabinet cooler

Generator power monitoring

Remote relay panel

Turbocharger speed sensors

Cylinder pressure relief valve

Oil mist detector

Flywheel and damper guards

Mounting System

Base aseembly

Vertically-restrained vibration isolators and weld plates

Starting System

Single turbine air starters

Boost control valve for extremely cold ambient conditions

Air start pressure reducing valves

General

Torsional couplings

Mounting groups for engine, generator, and base

Accessory module to mount attachments such as the expansion tank, heat exchanger, instrument panel and engine controls, annunciator panel, alarm and shutdown contactors, fuel strainer

Flywheel

Engine barring device options:

One-year storage preservation

Oceanic transportation shipping protection (shrink wrap and tarp)

Engine testing — certified dynamometer test, fuel consumption test, rated speed performance test, overload test, minimum power setting, peak firing pressure test, turbo work cert and crankshaft work cert

Standard and project-specific witness testing

Spare parts kit

Literature

Project-specific installation drawings

Electrical schematics and P&ID drawings